Acutherm ADVANTAGE VAV diffusers enhance traditional system design by adding personal control. Room temperature sensors provide constant feedback to the controller located in the diffuser, enabling precise monitoring of the space temperature.
Discover the ADVANTAGE:
• Superior air distribution
• No dumping
• More entrainment
• Even temperature distribution
• Better room air change effectiveness
• Power: Electric Motor
• Network: BACnet MS/TP
For more information, please Contact Us.
Every Therma-Fuser™ Motorised VAV diffuser is a VAV zone of temperature control providing pleasing comfort in both heating and cooling. A wide range of control is available with comfort set points adjustable from 13-35˚C. The electric motor delivers a consistent response for control of room temperature, and when required, a quick response to commands. The Wall Adjuster provides easy access for unit configuration and for the occupant to adjust comfort set points.
The need for any maintenance or repair is minimized through the robust design and a brushless DC stepper motor specifically selected for a long life. The electric motor directly drives a threaded shaft connected with a linkage to the dampers eliminating the need for a failure prone gear box. The control algorithm reduces the motor run time to a minimum reducing energy use and extending the motor life. And, should maintenance be required, the unique design allows for easy access to the motor from the room without removal of the diffuser from the ceiling.
Only Therma-Fuser™ Motorised VAV Diffusers offers these Benefits:
• Quiet – no motor noise
• Separate temperature set points for VAV heating and VAV cooling
• Superior air distribution – longer throws, no dumping, more entrainment, even temperature distribution, higher ADPI* and better room air change effectiveness
• Lowest energy VAV terminalgreen VAV
• Low to no maintenance- 2 year warranty
• Easily adapts to office changes
How the Standalone Motorised VAV Diffuser Works
Model MF Therma-Fuser diffusers are nominal 600mm square ceiling diffusers with built in DDC controller, temperature sensors and VAV damper. Four damper blades open and close to meter air flow (hot or cold) into the room in response to room temperature. The dampers are modulated by a brushless DC stepper motor. The electric motor, rigorously tested to provide many years of reliable service, directly drives a threaded shaft connected with a linkage to the damper blades.
The controller uses an ‘expert system’ control similar to having an “expert” sitting there making the adjustments. Unlike PID control, ‘expert system’ control does not require field tuning. Every 10 seconds it determines if the flow should be adjusted and the amount of any adjustment based on temperature relationships and the rate of change.
For more information contact ecoHVAC.
An Interoperable VAV Diffuser (EF Therma-Fuser) that works with your Building Automation System? Yes!
Designed similarly to Acutherm’s independent models, the E-series Therma-Fuser diffusers recognize changes in room conditions and adjust control output for optimal performance. The result is individual temperature control that precisely matches the comfort requirements of the room.
Acutherm Interoperable Therma-Fuser diffusers are specifically designed for application in multi-vendor DDC building control networks that use LonWorks® technology.
As a supporter of LonMark®, Acutherm is working to make interoperability easy. All E-series Therma-Fuser diffusers are compliant under LonMark® interoperability guidelines.
TECHNOLOGICALLY ADVANCED COMFORT
Experience the benefits of high tech, high quality Acutherm products
• Superior air distribution – longer throws, no dumping, more entrainment, even temperature distribution, higher ADPI and better ventilation effectiveness.
• Lowest cost per zone of control.
• Lowest energy VAV terminal – green VAV.
• Low to no maintenance and no need for field tuning or calibration thanks to highly reliable thermal actuators.
• Easily adapts to office changes.
To learn more visit www.ecohvac.com.au.
Read what green-buildings.com has to say about LEED and the Therma-fuser…
Therma-Fuser diffuser is a fully integrated, independent zone VAV control system including thermostat, modulating damper and diffuser in a single package. Unlike conventional building controls, Therma-Fuser diffusers require no wiring and operate automatically and independently. Therma-Fuser diffusers require little or no maintenance. Therma-Fuser diffusion dampers operate by opening and closing automatically to regulate air flow into the room in response to room temperature.
The dampers are mechanically actuated by thermal element thermostats. Each thermal element thermostat is a small brass cylinder containing petroleum-based wax. The wax expands when heated, driving a piston out. A spring retracts the piston when the wax cools and retracts. The movement of the piston either opens or closes the air dampers in a proportional manner.
Average room temperature is monitored by inducing a sample of air from the center of the room across the thermal element thermostats. Because this air sample is drawn directly from the air circulation pattern in the room, just before it mixes with air flowing into the room, it better represents average room temperature than air at a wall thermostat.
With Therma-Fuser diffusers, room temperature throughout the room can be held within 1 1/2º F of the temperature selected. Temperature of the room is selected between 70º and 78º F by adjusting the thermal element thermostat.
Article available at www.green-buildings.com.
For additional information on the Therma-Fuser VAV Diffuser visit www.ecohvac.com.au.
Acutherm Therma-Fuser™ VAV Diffuser System, recently joined and integrated their products BACnet International.
Acutherm, a manufacturer of components for heating and air conditioning systems, recently joined as part of their work in integrating one of their signature products. “Acutherm’s Therma-Fuser™ VAV System is designed to work cooperatively with a wide range of Building Automation System options,” stated Robert Kline LEED AP BD+C, Engineering Manager at Acutherm. “The association with BACnet International and the resources it has to offer, such as the BACnet Test Lab, is an important element for integrating our VAV Diffusers with other building components.”
As a silver member, Acutherm joins over 80 of the leading building automation vendors in the world in pursuing advancement of this communication protocol.
“Acutherm’s work in ensuring their products integrate using BACnet is a valued initiative,” stated Andy McMillan, President of BACnet International and Philips Teletrol. “Their participation in BACnet International helps facilitate successful implementation of the BACnet Standard.”
For more detailed information, please contact your nearest ecoHVAC representative or visit www.ecohvac.com.au.
Acutherm manufactures components for heating and air conditioning systems that make commercial buildings more comfortable, save energy, offer sustainability and can also reduce total installed costs. Our components are called Therma-FuserTM variable air volume (VAV) diffusers. They are used in VAV air conditioning systems which, instead of varying the temperature of the cooling air, vary the amount of the cooling air to maintain even room temperatures.
ecoHVAC proudly receives two awards from Acutherm: 2012 Grand Champion and 2012 Goal Buster. Well done to all of those involved.